ASTM D5035 纺织品的断裂强力和伸长率-条样法

ASTM D5035 textile testing

 ASTM D5035 provides a testing procedure for determining the maximum force and elongation at maximum force of various textile fabrics using raveled strip and cut strip methods of testing. If required, the force and elongation at rupture are recorded as well. 

The raveled testing method is mainly applicable to woven fabrics, whereas the cut strip test is mainly applicable to nonwoven, dipped or coated fabrics, and felted fabrics. However, the methods from this testing procedure are not meant for knitted fabrics or others with high breaking elongation. It is important to review the full standard in order to fully understand the test setup, procedure, and results requirements.

Materials Testing System

As with most textiles testing, it is important to consider data rate when choosing a testing instrument. To consistently and accurately measure the tear strength of your material, it is important to remember that the data sampling rate needs to be high enough that the test peaks and troughs are adequately captured. We recommend Instron’s high tier 6800 Series systems due to their data capture rate of up to 5 kHz. For most textile fabrics testing to ASTM D5035, a single column frame is appropriate as the loads rarely go above 5 kN.




ASTM D5035 Test Setup
1) 6800 Series Universal Testing System
2) Bluehill Universal Software
3) 2580 Series Load Cell
4) 2712-045 Pneumatic Side Action Grips

 

ASTM D5035 system setup
Grips 

Specimens tested to ASTM D5035 are paired with adequate grips utilizing jaw faces that include a minimum width at least 10 mm wider than the width of the specimen with a minimum height of 25 mm. Though manual grips are acceptable, pneumatic side action grips are recommended due to their ease of use, high repeatability, and high throughput. Adjustable grip pressure also allows users to fine-tune the gripping pressure to avoid jaw breaks or slippage.

ASTM D5035 calls out utilizing smooth and flat jaw faces for testing, but this primarily depends on the material being tested. Rubber coated jaw faces are often the first choice, and in some cases where the fabric specimen is strong or slippery, serrated jaw faces may be more appropriate. The standard also calls out the ability to use extra padding material within the jaw faces such as paper or emery cloth as an additional way to help prevent slippage.

2712-045
5 kN Model | 2712-045
Tips and Tricks
  • This standard recommends a Constant Rate of Extension (CRE) frame for testing, however, it also notes that Constant Rate of Load or Constant Rate of Traverse are acceptable as well. When different testing machines are used for testing the same materials, a constant time-to-break of 20 +/- 3 seconds is recommended for the most comparable results. It should be noted that results still can vary significantly based on the frame used.
  • ASTM D5035 requires that two sets of specimens are prepared, one in the warp direction and one in the weft direction.
  • Instron’s Bluehill Universal testing software has advanced pre-built methods available with pre-configured calculations helping to ensure compliance to ASTM D5035.

Related Content

6800 系列高级测试系统宣传册

Instron 6800 系列通用测试系统可提供无与伦比的准确性和可靠性。6800 系列以专利申请中的操作员保障系统架构为依托,架构采用全新的 Smart-Close 空气套件并具有碰撞缓解功能,使得材料测试比以往任何时候都更简单、更智能、更安全。

Bluehill Universal 宣传册

Bluehill Universal 软件从头开始构建,旨在提供触摸互动和直观的用户体验。使用诸如预装测试方法、几秒钟内快速测试、增强的数据导出以及 Instron Connect(一种全新功能,可提供与服务的直接通信联系)等功能,发现更简单、更智能的测试。 Bluehill 2 和 Bluehill 3 等以前版本软件的用户可以轻松升级到最新版本的 Bluehill。

2712-04X 系列气动侧动夹具

气动侧动夹具为各种材料提供了通用夹持解决方案。额定容量 1 - 10 kN。