ASTM D5035 纺织品的断裂强力和伸长率-条样法

ASTM D5035 textile testing

 ASTM D5035 provides a testing procedure for determining the maximum force and elongation at maximum force of various textile fabrics using raveled strip and cut strip methods of testing. If required, the force and elongation at rupture are recorded as well. 

The raveled testing method is mainly applicable to woven fabrics, whereas the cut strip test is mainly applicable to nonwoven, dipped or coated fabrics, and felted fabrics. However, the methods from this testing procedure are not meant for knitted fabrics or others with high breaking elongation. It is important to review the full standard in order to fully understand the test setup, procedure, and results requirements.

Materials Testing System

As with most textiles testing, it is important to consider data rate when choosing a testing instrument. To consistently and accurately measure the tear strength of your material, it is important to remember that the data sampling rate needs to be high enough that the test peaks and troughs are adequately captured. We recommend Instron’s high tier 6800 Series systems due to their data capture rate of up to 5 kHz. For most textile fabrics testing to ASTM D5035, a single column frame is appropriate as the loads rarely go above 5 kN.




ASTM D5035 Test Setup
1) 6800 Series Universal Testing System
2) Bluehill Universal Software
3) 2580 Series Load Cell
4) 2712-045 Pneumatic Side Action Grips

 

ASTM D5035 system setup

Grips 

Specimens tested to ASTM D5035 are paired with adequate grips utilizing jaw faces that include a minimum width at least 10 mm wider than the width of the specimen with a minimum height of 25 mm. Though manual grips are acceptable, pneumatic side action grips are recommended due to their ease of use, high repeatability, and high throughput. Adjustable grip pressure also allows users to fine-tune the gripping pressure to avoid jaw breaks or slippage.

ASTM D5035 calls out utilizing smooth and flat jaw faces for testing, but this primarily depends on the material being tested. Rubber coated jaw faces are often the first choice, and in some cases where the fabric specimen is strong or slippery, serrated jaw faces may be more appropriate. The standard also calls out the ability to use extra padding material within the jaw faces such as paper or emery cloth as an additional way to help prevent slippage.

2712-045
5 kN Model | 2712-045

Tips and Tricks

  • This standard recommends a Constant Rate of Extension (CRE) frame for testing, however, it also notes that Constant Rate of Load or Constant Rate of Traverse are acceptable as well. When different testing machines are used for testing the same materials, a constant time-to-break of 20 +/- 3 seconds is recommended for the most comparable results. It should be noted that results still can vary significantly based on the frame used.
  • ASTM D5035 requires that two sets of specimens are prepared, one in the warp direction and one in the weft direction.
  • Instron’s Bluehill Universal testing software has advanced pre-built methods available with pre-configured calculations helping to ensure compliance to ASTM D5035.

Related Content

6800 Series Premier Testing Systems Brochure

Instron 6800 Series Universal Testing Systems provide unparalleled accuracy and reliability. Built on a patent-pending Operator Protect system architecture with an all-new Smart-Close Air Kit and Collision Mitigation features, the 6800 Series makes materials testing simpler, smarter, and safer than ever before.

Bluehill Universal Brochure

Bluehill Universal Software is built from the ground-up for touch interaction and an intuitive user experience. Discover simpler and smarter testing with features such as pre-loaded test methods, QuickTest in seconds, enhanced data exporting: and Instron Connect – a new feature that provides a direct communication link to Service. Users of previous versions of software such as Bluehill 2 and Bluehill 3 can easily upgrade to the newest version of Bluehill.

2712-04X Series Pneumatic Side-Action Grips

Pneumatic side-action grips offer a versatile gripping solution for a wide range of materials. Rated capacities between 1 and 10 kN.